Plumbing Basics: An Essential for Installing a Bathtub
Plumbing Basics: An Essential for Installing a Bathtub
Blog Article
Just how do you actually feel with regards to A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely rocket science, yet it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably hard task. If the old tub is readily available, the task can move quickly; if you need to open up a wall to eliminate the old bathtub and place the new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to move out the old tub and embeded in the new one. Ensure you have actually certified on your own for the work and are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This post will assist you mount a brand-new tub in your shower room if you have currently acquired a brand-new bathtub and don't need to transform the arrangement of your previous supply of water pipes.
Your devices and also material list need to comprise the following:
Planning for the Installment
Firstly, the sustaining frame provided with the bath should be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps device to stop stress on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any water staying in the system. The process of removing the existing taps can be quite troublesome because of the restricted gain access to that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have been removed, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this process. When the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before proceeding to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, position the bath tub in the required setting. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by checking the level as well as readjusting the feet on the bathtub up until the level reads level.
To install faucets, fit all-time low of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water and check all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bath tub as well as additionally examine the overflow electrical outlet and the normal outlet for leakages.
Finally, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the tub has been used a minimum of when as this will certainly resolve it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in place between the faucet and the sink. Secure the faucet in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to break an inflexible seal, causing the water to pass through the wall surface between the bathroom and also the tiling, causing complications with wetness and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and also installations. They are marketed in tubes and cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to always fill the bathtub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealant can crack relatively very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our post about How to Install a Bathtub Yourself. Thank you for finding the time to read our post. So long as you enjoyed reading our blog post if you please don't forget to share it. We take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Reliable plumber? Dial now! Report this page